Formulations

Tuffbond® 310 adhesive/sealant is a two-component epoxy, 100% solid system, two to one ratio, room temperature cure system. Tuffbond® 310 is recommended for bonding metals, wood, and ceramics.

Tuffbond® 394 is a single component, high temperature resistant, heat activated epoxy. It cures to a high-performance thermoset system with excellent adhesion properties to a wide variety of substrates. Tuffbond® 394 will change from amber-yellow to a reddish brown upon cure. Bonding the voice coil to the cone has been a challenge for engineers, specifically when the adhesive temperature resistance requirement is above 200°F (93°C). Two component epoxy was commonly used for this application, but limitations such as mixing ratio, cure speed, potential solidification in equipment and the need for equipment flushing solvents have made Tuffbond® 394 more practical.

Rust Eliminator 32 is a new revolutionary product for eliminating old rust and preventing new rust on steel parts. Rust is chemically transformed into an inert, non-corrosive coating.

Primer 50 is a single component, non-CFC solvent-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 50 is used where increased cure speed of Hernon® anaerobic adhesives and sealants is required. It is especially recommended for applications with passive metals or inert surfaces and with large bond gaps. It is particularly recommended for cure conditions below 15°C. Primer 50 meets the requirements of ASTM D5363 (Grade N) and MIL-S-46163A Grade F.

Tuffbond® 395 is a single component, high temperature resistant, heat activated epoxy. It cures to a high-performance thermoset system with excellent adhesion properties to a wide variety of substrates. Tuffbond® 395 will change from amber to a reddish brown upon cure. Bonding the voice coil to the cone has been a challenge for engineers, specifically when the adhesive temperature resistance requirement is above 200°F (93°C). Two component epoxy systems have been most commonly used for this application, but limitations such as mixing ratio, cure speed, potential solidification in equipment and static mixers and the need for equipment flushing solvents have made Tuffbond® 395 more practical.

DEACTIVATOR FOR UV FOG, 500 GRAMS

Hernon External Ammunition Sealant 76070 is a single component, U.V curable anaerobic sealant. 76070 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. This sealant is specially formulated for Ammunition that needs greater fit tolerance and higher bullet pull forces. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic suitable and endures exposure to most solvents. Ammunition Sealant 76070 cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to three minutes, Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure. Product Benefits • UV fluorescence for in-process inspection • 100% solid system (no solvents) • Excellent environmental resistance • Good gap filling properties • Excellent Bullet Pull strengths with low Standard deviation • UV and anaerobic curing mechanism suitable for metal parts • Good capillary performance • Good performance on frangible bullets

CM8005 is a single-component room temperature cure gel-like anaerobic gasketing compound formulated to provide instant sealing capabilities. Once cured between mating metal flanges and filling voids in the surface, CM8005 provides a thin, flexible, solvent and temperature resistant seal.

Tuffbond® 313 adhesive/sealant is a two component, 100% solid system, one to one ratio, room temperature cure system. Tuffbond® 313 is recommended for bonding metals, wood, ceramics, etc., and can be used for potting and encapsulation of electrical and electronic components.

Nuts N’ Bolts® 423 is a single component anaerobic thread locking material, which is thixotropic and develops medium strength. The product cures when confined in the absence of air between close fitting metal surfaces and is particularly suitable for less active substrates such a stainless steel and plated surfaces.

Ultrabond® 3444 is a single component, tri-cure conformal coating formulated for bonding glass to glass or glass to metals. Ultrabond® 3444 is excellent for bonding and tacking many parts. Ultrabond® 3444 can also be cured with heat above 200°F (93°C) or Activator 56. Exposure to a high intensity UV light will cure these adhesives to a dry, hard surface.

Hernon 397 is a single component, high temperature resistant, heat activated epoxy. It cures to a high-performance thermoset system with excellent adhesion properties to a wide variety of substrates. Tuffbond 397 will change from amber-yellow to a reddish brown upon cure. Product Benefits • High temperature resistance. • Single component (no mixing, no pot life). • Contains 150micron spacer beads for bond line control • Solventless. • Cures on demand (heat cure). • Will not slip during cure. • Changes color upon cure (yellow to brown). • Excellent adhesion to various substrates. • Gives high shear. • Low water absorption.

Hernon® Ultrabond® 750 is a UV curable adhesive that can be used to seal a variety of plastics when exposed to UV light. The sealant offers a water- tight seal with excellent environmental resistance. Prevents material escaping through a crimped seal. With Ultrabond 750 a low powered UV lamp (Blacklight), can be used to inspect for the presence of adhesive on the substrates. Product Benefits • UV fluorescence for in-process inspection •Cures well at 395nm •Flexible thermoset system • Excellent Water Resistance •Good adhesion to a variety of plastics • 100% solid system (no solvents) • Good gap filling properties • No shrinkage due to solvent evaporation • Rapid UV cure

Hernon® External Ammunition Sealant 76984 is a single component high strength U.V. anaerobic sealant. 76984 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. This Sealant is specially formulated for Ammunition that needs greater fit tolerance and higher bullet pull forces. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic and endures exposure to most solvents. Ammunition Sealant 76984 cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to three minutes, Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure. Product Benefits • UV fluorescence for in-process inspection • 100% solid system (no solvents) • Excellent environmental resistance • Good gap filling properties • Excellent Bullet Pull strengths with low Standard deviation. • UV and anaerobic curing mechanism suitable for metal parts • Good capillary performance

Dissipator® 745 is a thermally conductive room temperature cure adhesive that is designed for bonding electrical components to heat sink with a controlled gap. Dissipator® 745, through a special shimming property, insulates the component electrically while allowing thermal conductivity. This special shimming feature produces a constant gap of 0.005 in. to 0.006 in. between components.

Silastomer® 333 is a high performance, single component, ready to use adhesive / sealant. It has a paste-like consistency, which cures to a tough, resilient and durable silicone rubber when exposed to moisture in the air. Since it will not flow of its own weight, Silastomer® 333 can be applied to vertical, horizontal and overhead joints without sagging or running off. It will adhere to clean metals, glass, most types of wood, silicone resin, vulcanized silicone rubber, natural and synthetic fiber, ceramic, many plastics and painted surfaces. Silastomer® 333 provides excellent resistance to moisture, weathering, vibration, ozone and extreme temperatures. It can be applied in surface temperatures of 0°F to above 120°F with no loss in performance. Fully cured Silastomer® 333 can withstand extended periods at temperatures up to 400°F.

Silastomer® 343 is a black, high performance, single component, ready to use adhesive / sealant. It has a paste-like consistency, which cures to a tough, resilient and durable silicone rubber when exposed to moisture in the air. Designed to provide excellent oil resistance and can be used as a form in place gasket. It will adhere to clean metals, glass, most types of wood, silicone resin, vulcanized silicone rubber, natural and synthetic fiber, ceramic, many plastics and painted surfaces. Silastomer® 343 provides excellent resistance to moisture, weathering, vibration, ozone and extreme temperatures. It can be applied in surface temperatures of 0°F to above 120°F with no loss in performance. Fully cured Silastomer® 343 can withstand extended periods at temperatures up to 400°F.

Silastomer® 336 is a high performance, single component, acetoxy, ready to use silicone. It has a paste-like consistency, which cures to a tough, resilient and durable silicone rubber when exposed to moisture in the air. Since it will not flow of its own weight, Silastomer® 336 can be applied to vertical, horizontal and overhead joints without sagging or running off. It will adhere to clean metals, glass, most types of wood, silicone resin, vulcanized silicone rubber, natural and synthetic fiber, ceramic, many plastics and painted surfaces. Silastomer® 336 provides excellent resistance to moisture, weathering, vibration, ozone and extreme temperatures. It can be applied in surface temperatures of 0°F to above 120°F with no loss in performance. Fully cured Silastomer® 336 can withstand extended periods at temperatures up to 400°F.

Silastomer® 340 is a one-component, acetoxy, moisture curing RTV (room temperature vulcanizing) ready-to-use adhesive / sealant and gasketing compound. Can be used as a form in place gasket material where temperatures may reach up to 600°F. Silastomer® 340 will remain flexible with excellent resistance to aging and vibration. Meets MIL-A-46106B Type 1 requirements. FDA compliant with Regulation Title 21 CFR 175.105 where incidental food contact may be involved.